Interstate standard GOST 8273-75
"Wrapping paper. Specifications"
(approved by the resolution of the State Standard of the USSR of March 24, 1975 N 721)
packing paper. Specifications
Instead of GOST 8273-57
1. Brands and sizes
1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:
A - from sulfate unbleached pulp;
B - from sulfate wrapping pulp;
B - from sulfite unbleached pulp;
G - from sulfite wrapping pulp and wood pulp;
From sulfate, sulfite bleached pulp;
From sulphate, sulfite bleached pulp, sulfite unbleached pulp and wood pulp;
D - from unbleached pulp, semi-cellulose and wood pulp;
E - from waste paper, unbleached pulp and fibrous waste from pulp and paper production.
F - the composition is not standardized.
(Changed edition, Rev. N 1).
1.2. Paper grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.
(Changed edition, Rev. N 3).
1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of the sheet paper are set by agreement between the manufacturer and the consumer.
Maximum deviations in paper sizes of all brands should not exceed mm, in paper intended for processing on automatic machines - mm.
Example symbol wrapping paper brand A with a mass of paper with an area of 190 g:
Paper wrapping stamps A-90 GOST 8273.
(Changed edition, Rev. N 2, 3).
2. Technical requirements
2.1a. Paper must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.
(Introduced additionally, Rev. N 2).
2.1. Paper quality indicators must comply with the standards specified in the table.
|
Name of indicator |
Norm for paper stamps |
Limit deviations |
Test method |
||||||||
|
1. Mass of paper with an area of 1 m2, g |
For paper grades A, B, O_1, O_2, D with an area weight of 1 m2 up to (90+-2) g For paper of other brands and mass +-4_5 |
||||||||||
|
2. Relative bursting strength, kPa (kgf/cm2), not less than, for paper with an area of 1 m2, g |
GOST 13525.8 |
||||||||||
|
3. Breaking length on average in two directions, m, not less, for a mass of paper with an area of 1m2, g |
GOST 13525.1 |
||||||||||
Decree of the State Committee for Standards of the Council of Ministers of the USSR dated March 24, 1975 No. 721
deadline set
from 01.01.76
Decree of the State Standard of March 27, 1985 No. 880
expiration date extended
until 01.01.91
This standard applies to paper intended for packaging food, medicines and industrial products.
Mandatory requirements for product quality are set out in clause 2.1 (table, indicators 2-5)
* Reissue (March 1986) with Amendments No. 1, 2, approved in January 1981, March 1985 (IUS 3-81, 6-85).
1. GRADES AND SIZES
1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:
A - from sulfate unbleached pulp;
B - from sulfate wrapping pulp;
B - from sulfite unbleached pulp;
G - from sulfite wrapping pulp and wood pulp;
About 1 - from sulfate, sulfite bleached pulp;
O 2 - from sulphate, sulfite bleached pulp, sulfite unbleached pulp and wood pulp;
D - from unbleached pulp, semi-cellulose and wood pulp;
E - from waste paper, unbleached pulp and fibrous waste from pulp and paper production.
F - the composition is not standardized.
(Changed edition, Rev. No. 1, No. 3).
1.2. Paper grades V, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.
(Changed edition. Rev. No. 3).
1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of the sheet paper are set by agreement between the manufacturer and the consumer.
Maximum deviations in paper sizes of all brands should not exceed ±5 mm, in paper intended for processing on automatic machines - ±2 mm.
An example of a symbol for wrapping paper brand D with a mass of paper with an area of 1 m 2 90 g:
Wrapping paper brand A-90 GOST 8273-75.
2. TECHNICAL REQUIREMENTS
2.1a. Paper must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.
(Introduced additionally, Amendment No. 2).
2.1. Paper quality indicators must comply with the standards specified in the table.
(Revised edition, Rev. No. 1).
|
Name of indicator |
Norm for paper stamps |
Limit deviations |
Test method |
||||||||
|
1. Weight of paper with an area of 1 m 2, g |
For paper grades A, B, O 1, O 2, D with an area weight of 1 m 2 up to (90 ± 2) g |
||||||||||
|
For paper of other brands and weights |
|||||||||||
|
2. Relative bursting resistance, kPa (kgf/cm 2), not less than, for paper with an area of 1 m 2, g |
|||||||||||
|
3. Breaking length on average in two directions, m, not less, for a mass of paper with an area of 1 m 2, g |
|||||||||||
|
4. Degree of sizing, mm, not less |
|||||||||||
|
5. Humidity, %, no more |
|||||||||||
Notes:
1. By agreement with the consumer, it is allowed to produce paper grades A, B, D weighing 1 m 2 90 g or more with a breaking length of at least 5000, 3300, 2400 m, respectively.
brand E weighing 1 m 2 60 g or more with a breaking length of at least 2000 m;
brand Zh weighing 1 m 2 90-120 g with a breaking length of at least 2900 m;
weighing 1 m 2 130-160 g with a breaking length of at least 2700 m.
(Changed edition. Rev. No. 3).
2.2. By agreement between the manufacturer and the consumer, it is allowed to produce non-glued paper of all grades.
2.3. Paper is produced by machine, single-sided and double-sided smoothness.
2.4. Paper should be made in natural fiber color or dyed.
For packaging bulk food products, it is allowed to use paper dyed in various colors with dyes approved by the USSR Ministry of Health; for packaging other food products, the use of colored paper is not allowed.
2.5. Paper grades V, D, O 1 and O 2, intended for printing, must be produced with an ash content of at least 8% and a breaking length of at least 1700 m.
(Changed edition, Rev. No. 1, No. 3).
2.5a. By agreement with the consumer, it is allowed to produce paper grades A and E with a moisture content of up to 11%.
(Introduced additionally. Amendment No. 3).
2.6. Folds, tears, holes that cannot be detected during rewinding are allowed in roll paper if the mass of sheets with such defects, determined in accordance with GOST 13525.5-68, does not exceed 5%, and in roll paper intended for processing: industry, - 3%.
2.7. For paper intended for recycling by automatic machines, the winding of the roll paper must be uniform and dense, the cut edges must be even and clean.
(Changed edition. Rev. No. 3).
2.8. The number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in food industry machines, it should not exceed three.
2.9. The places of breaks in paper intended for processing on automatic machines must be glued together and marked with color signals visible from the end of the roll.
3. ACCEPTANCE
(Changed edition. Rev. No. 3).
3.1. The definition of the party and the sample size - in accordance with GOST 8047-78.
3.2. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on it on a double sample from the same batch.
The retest results apply to the entire lot.
(Revised edition, Rev. No. 2).
4. TEST METHODS
4.1a. Sampling and preparation for testing - according to GOST 8047-78.
(Introduced additionally, Amendment No. 2).
4.1. Paper conditioning before testing and testing is carried out in accordance with GOST 13523-78 at relative humidity air (50±2)% and temperature (23±1) °С.
The duration of conditioning is at least 2 hours.
(Changed edition, Rev. No. 2, No. 3).
4.2. Paper sizes are determined according to GOST 21102-80.
4.3. When determining the mass fraction of ash, the calcination temperature is set to (575 ± 25) ° C according to GOST 7629-77.
(Introduced additionally, Rev. No. 2, No. 3).
5. PACKAGING, LABELING, TRANSPORT AND STORAGE
5.1. Packaging, marking, storage and transportation - according to GOST 1641-75 with the following addition:
5.1.1. The labeling of paper not intended for food packaging is supplemented by the warning label “non-food”.
5.2. The roll diameter must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, which is not intended for processing on automatic machines.
5.1, 5.2. (Revised edition, Rev. No. 2).
5.3. (Deleted, Rev. No. 2).
5.4. (Deleted, Rev. No. 3).
5.5. (Deleted, Rev. No. 2).
The standard providing for the production and characteristics of wrapping paper is GOST 8273-75. It contains all the standards associated with this material that affect the quality of the finished product, dimensional tolerances, as well as storage and transportation conditions.
Specifications
Pakland LLC products manufactured in accordance with GOST comply with all sanitary and hygienic standards and can be used in food packaging. The material does not allow moisture and grease to pass through, and is additionally used for packaging flowers, books, parcels, dishes and other consumer goods.
It is produced in rolls and sheets on modern automated equipment under the strict guidance of experienced specialists, which completely eliminates the appearance of defects, so we guarantee the quality of the goods we supply to our customers.
Even metal objects can be packed into it, but there are already certain limitations, so an individual approach is needed. Our managers are ready to advise and explain all the technical nuances of using this product.
Paper grades
The following paper grades are available:
- O1;
- O2;
The most popular of these is brand E wrapping paper. Their quality decreases from the first to the last brand, but so does the cost. E performance does not drop much. That is why cheap materials are more popular.
The density of the material varies from 60 to 160 g/m2, and 80 g/m2 is the most popular today.
You can buy wrapping paper GOST 8273-75 at a low price at Packland. We offer significant discounts on wholesale lots, but we also work with retail. Our clients include both individuals and legal entities not only in Moscow and the region, but throughout Russia.
| Designation | GOST 8273-75 |
| Title in Russian | Wrapping paper. Specifications |
| Title in English | packing paper. Specifications |
| Date of entry into force | 01.01.1976 |
| OKS | 55.040 |
| OKP code | 543500 |
| KGS code | K68 |
| OKSTU code | 5435 |
| SRSTI rubricator index | 664533; 664537 |
| Annotation (scope) | This standard applies to paper intended for packaging foodstuffs, medicines and industrial products. |
| Keywords | wrapping paper; brands; dimensions ; quality indicators ; |
| Type of standard | Standards for products (services) |
| Type of requirements | Requirements for mandatory certification; The document is marked * |
| Designation of the replacement(s) | GOST 8273-57 |
| Normative references to: GOST | GOST 1641-75; GOST 7629-93; GOST 8047-93; GOST 8049-62; GOST 13199-88; GOST 13523-78; GOST 13525.1-79; GOST 13525.5-68; GOST 13525.8-86; GOST 13525.19-91; GOST 21102-80 |
| Department of Rostekhregulirovanie | 320 - Management of standardization and certification of raw materials and materials |
| MND developer | Russian Federation |
| Interstate TC | 177 - Cellulose, paper, cardboard and industrial and technical materials for various purposes |
| Date of last edition | 01.10.1998 |
| Number(s) of change(s) | reissue with rev. 1; 2; 3 |
| Number of pages (original) | 8 |
| Organization - Developer | Ministry of Forestry of the USSR |
| Status | Active |
WRAPPING PAPER
TECHNICAL CONDITIONS
GOST 8273-75
USSR STATE COMMITTEE
Moscow
STATE STANDARD OF THE UNION OF THE SSR
Decree of the State Committee for Standards of the Council of Ministers of the USSR dated March 24, 1975 No. 721
deadline set
from 01.01.76
Decree of the State Standard of March 27, 1985 No. 880
expiration date extended
until 01.01.91
paper for food packaging , medicines and industrial products.
Mandatory requirements for product quality are set out in clause 2.1 (table, indicators 2-5)
* Reissue (March 1986) with Changes No. 1, 2 , approved in January 1981, March 1985 (IUS 3-81, 6-85).
DIMENSIONS depending on the purpose and quality indicators wrapping paper should be produced in nine grades:
A- from sulfate unbleached pulp;
B - from sulfate wrapping pulp;
B - from sulfite unbleached pulp;
G - wrapping pulp and wood pulp;
Sulfite bleached pulp;sulfite bleached pulp , sulfite unbleached pulp and wood pulp; cellulose, semi-cellulose and wood pulp ; pulp and fibrous waste from pulp and paper production. The position is not standardized. Revised edition, Amend. No. 1, No. 3).Rock B, D, F and G of food and drug packaging , must be made with a composite composition, approved by the Ministry of Health of the USSR.
(Changed edition. Rev. No. 3).
and produced in rolls and sheets. The width of the rolls and the dimensions of the sheet paper are set by agreement between the manufacturer and the consumer. The dimensions of the paper of all brands should not exceed the paper intended for processing on automatic machines - ± 2 mm. measures of the symbol for wrapping paper brand D with a mass of paper with an area of 1 m 2 90 g: A-90 GOST 8273-75.ya, Amend. No. 2, No. 3).
2. TECHNICAL REQUIREMENTS
prepared in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner. No. 2). paper quality must comply with the standards specified in the table. edition, Amend. No. 1).|
Name of indicator |
Norm for paper stamps |
Limit deviations |
Test method |
||||||||
|
1. Mass of paper with an area of 1 m 2 , G |
For paper grades A , B , About 1 , About 2 , D with an area mass of 1 m 2 up to (90 ± 2) g |
||||||||||
|
For paper of other brands and weights |
|||||||||||
| 60 | |||||||||||
| 5 | |||||||||||
| 0 | |||||||||||
| bursting resistance, kPa (kgf / cm3, not less, for paper with an area of 1 m g | 25.8-86 | ||||||||||
| breaking length on average in two directions, m, not less than for a mass of paper with an area of 1 m 2 , G |
GOST 13525.1-79 |
||||||||||
| 00 | |||||||||||
| 55 | 500 | 700 | 00 | ||||||||
| 000 | |||||||||||
| 200 | |||||||||||
| 0-120 | 00 | 00 | 00 | 600 | 0 | ||||||
| 0-160 | |||||||||||
|
4. Degree of sizing , mm , at least |
GOST 8049-62 |
||||||||||
|
5. Humidity , %, no more |
-71 | ||||||||||
Notes on agreement with the consumer it is allowed to produce paper grades A , IN, D weighing 1 m 2 90 g or more with a breaking length of 5000, respectively
E weighing 1 mee with a breaking length of at least 2000 m ;
Rki Zh weighing 1 m, length not less than 2900 m
Oh, at least 2700 m long.
(Changed edition. Rev. No. 3).
between the manufacturer and the consumer, it is allowed to produce paper of all grades of non-glued, machine-made, one-sided and two-sided smoothness. for packaging other food products, the use of colored paper is not allowed. grades V, D, O 1 and O 2, intended for printing, must be made with an ash content of at least 8% and a breaking length of at least 1700 m. No. 1, No. 3).
2.5a. By agreement with the consumer, it is allowed to produce paper grades A and E with a moisture content of up to 11%.
(Introduced additionally. Amendment No. 3).
Tears, holes that cannot be detected during the rewinding process are allowed in roll paper if the mass of sheets with such defects, determined by the method, does not exceed 5%, and in roll paper intended for processing: on food industry machines - 3%. revised edition, Rev. No. 2), intended for processing on automatic machines, the winding of roll paper must be uniform and dense
(Changed edition. Rev. No. 3).
the number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in automatic food processing machines, it should not exceed three. in paper intended for processing in automatic machines, they must be glued together and marked with color signals visible from the end of the roll.
3. ACCEPTANCE
(Changed edition. Rev. No. 3).
e batch and sample size - according to GO ST 8047-78. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on a double sample from the same batch. Repeat tests apply to the entire batch. ennaya edition, Rev. No. 2).
4. TEST METHODS
4.1a. Sampling and preparation for testing - according to GOST 8047-78.
oh, change. No. 2). Paper rationing before testing and testing is carried out according to GOST 13523-78 at a relative humidity of air (50 ± 2) % and temperature (23± 1) ° C. conditioning - at least 2 hours.
(Changed edition, Rev. No. 2, No. 3).
4.2. Paper sizes are determined according to GOST 21102-80.
and the mass fraction of ash, the calcination temperature is set (575 ± 25) °С according to GOST 7629-77. eden additionally, rev. No. 2, No. 3). 2. Roll diameter must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, which is not intended for processing on automatic machines. edition, Rev. No. 2).
5.3. (Deleted, Rev. No. 2).
5.4. (Deleted, Rev. No. 3).
5.5. (Deleted, Rev. No. 2).
Directory of GOSTs, TU, standards, norms and rules. SNiP, SanPiN, certification, specificationsGOST 8273-75
Group K68
INTERSTATE STANDARD
WRAPPING PAPER
Specifications
packing paper. Specifications
OKP 54 3500
Introduction date 1976-01-01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Ministry of Forest Industry of the USSR
DEVELOPERS
I.A. Chizhova, O.A. Vasilyeva, Ph.D. tech. Sciences
2. APPROVED AND INTRODUCED BY Decree of the State Committee for Standards of the Council of Ministers of the USSR dated March 24, 1975 N 721
3. REPLACE GOST 8273-57
4. REFERENCE REGULATIONS AND TECHNICAL DOCUMENTS
Number of paragraph, subparagraph |
|
GOST 1641-75 | |
GOST 7629-93 | |
GOST 8047-93 | |
GOST 8049-62 | |
GOST 13199-88 | |
GOST 13523-78 | |
GOST 13525.1-79 | |
GOST 13525.5-68 | |
GOST 13525.8-86 | |
GOST 13525.19-91 | |
GOST 21102-97 |
5. The limitation of the validity period was removed according to protocol N 5-94 of the Interstate Council for Standardization, Metrology and Certification (IUS 11-12-94)
6. EDITION (November 2001) with Changes N 1, 2, 3, approved in January 1981, March 1985, March 1990 (IUS 3-81, 6-85, 6-90), Amendment (IUS 10-2001)
This standard applies to paper intended for packaging food products, medicines and industrial products.
Mandatory requirements* for product quality are set out in clause 2.1 (table, indicators 2-5).
________________
* Valid on the territory Russian Federation(Amendment, IUS 10-2001).
1. GRADES AND SIZES
1. GRADES AND SIZES
1.1. Depending on the purpose and quality indicators, wrapping paper should be produced in nine grades:
A - from sulfate unbleached pulp;
B - from sulfate wrapping pulp
B - from sulfite unbleached pulp;
G - from sulfite wrapping pulp and wood pulp;
O - from sulfate, sulfite bleached pulp;
O - from sulphate, sulfite bleached pulp sulphite, unbleached pulp and wood pulp
D - from unbleached pulp, semi-cellulose and wood pulp
E - from waste paper, unbleached pulp and fibrous waste from pulp and paper production.
F - the composition is not standardized.
(Changed edition, Rev. N 1).
1.2. Paper grades B, G, E and Zh, intended for packaging food products and medicines, must be made with a composition approved by the USSR Ministry of Health.
(Changed edition, Rev. N 3).
1.3. Paper must be produced in rolls and sheets. The width of the rolls and the dimensions of the sheet paper are set by agreement between the manufacturer and the consumer.
Maximum deviations in paper sizes of all brands should not exceed ±5 mm, in paper intended for processing on automatic machines - ±2 mm.
An example of a symbol for wrapping paper brand A with a mass of paper with an area of 1 m 90 g:
Wrapping paper brand A-90 GOST 8273.
2. TECHNICAL REQUIREMENTS
2.1a. Paper must be manufactured in accordance with the requirements of this standard according to the technological regulations approved in the prescribed manner.
2.1. Paper quality indicators must comply with the standards specified in the table.
Name of indicator | Norm for paper stamps | Limit- | test method |
||||||||
1. Weight of paper area | For paper grades A, B, O, O, D with area weight | ||||||||||
2. Relative- | GOST 13525.8 |
||||||||||
270 | |||||||||||
300 | |||||||||||
3. Breaking length on average in two directions, m, not less than for a mass of paper with an area | GOST 13525.1 |
||||||||||
4. Degree of sizing, mm, not less | |||||||||||
5. Humidity, %, no more | GOST 13525.19 |
||||||||||
Notes:
1. By agreement with the consumer, it is allowed to produce paper grades A, B, D weighing 1 m 90 g or more with a breaking length of at least 5000, 3300, 2400 m, respectively.
2 Paper containing more than 50% of waste paper and pulp and paper production waste in the composition is allowed to be produced:
brand E weighing 1 m 60 g or more with a breaking length of at least 2000 m;
brand Zh weighing 1 m 90-120 g with a breaking length of at least 2900 m;
weighing 1 m 130-160 g with a breaking length of at least 2700 m.
2.2. By agreement between the manufacturer and the consumer, it is allowed to produce non-glued paper of all grades.
2.3. Paper is produced by machine, single-sided and double-sided smoothness.
2.4. Paper should be made in natural fiber color or dyed.
For packaging bulk food products, it is allowed to use paper dyed in various colors with dyes approved by the USSR Ministry of Health; for packaging other food products, the use of colored paper is not allowed.
2.5. Paper grades V, D, O and O, intended for printing, must be produced with an ash content of at least 8% and a breaking length of at least 1700 m.
(Changed edition, Rev. N 1, 3).
2.5a. By agreement with the consumer, it is allowed to produce paper grades A and E with a moisture content of up to 11%.
(Introduced additionally, Rev. N 3).
2.6. Folds, tears, holes that cannot be detected during rewinding are allowed in roll paper, if the mass of sheets with such defects, determined in accordance with GOST 13525.5, does not exceed 5%, and in roll paper intended for processing on food industry machines, - 3%.
2.7. For paper intended for recycling by automatic machines, the winding of the roll paper must be uniform and dense, the cut edges must be even and clean.
(Changed edition, Rev. N 3).
2.8. The number of breaks in a roll should not exceed five, and in a roll of paper intended for processing in food industry machines, it should not exceed three.
2.9. The places of breaks in paper intended for processing on automatic machines must be glued together and marked with color signals visible from the end of the roll.
3. ACCEPTANCE
3.1. The definition of the lot and the sample size are in accordance with GOST 8047.
3.2. If unsatisfactory test results are obtained for at least one of the indicators, repeated tests are carried out on it on a double sample from the same batch.
The retest results apply to the entire lot.
(Changed edition, Rev. N 2).
4. TEST METHODS
4.1a. Sampling and preparation for testing - according to GOST 8047.
(Introduced additionally, Rev. N 2).
4.1. Paper conditioning before testing and tests are carried out according to GOST 13523 at relative air humidity (50 ± 2)% and temperature (23 ± 1) °C.
The duration of conditioning is at least 2 hours.
(Changed edition, Rev. N 2, 3).
4.2. Paper sizes are determined according to GOST 21102.
4.3. When determining the mass fraction of ash, the calcination temperature is set to (575 ± 25) ° C according to GOST 7629.
(Changed edition, Rev. N 2, 3).
5. PACKAGING, LABELING, TRANSPORT AND STORAGE
5.1. Packing, marking, storage and transportation - according to GOST 1641 with the following addition:
5.1.1. The labeling of paper not intended for food packaging is supplemented by the warning label "non-food".
5.2. The roll diameter must be at least 50 cm. At the request of consumers, a roll diameter of at least 35 cm is allowed, which is not intended for processing on automatic machines.
5.1-5.2. (Changed edition, Rev. N 2).
5.3. (Deleted, Rev. N 2).
5.4. (Deleted, Rev. N 3).
5.5. (Deleted, Rev. N 2).
ROSSTANDARD FA for technical regulation and metrology
NEW NATIONAL STANDARDS: www.protect.gost.ru
FSUE STANDARTINFORM provision of information from the database "Products of Russia": www.gostinfo.ru
FA FOR TECHNICAL REGULATION"Dangerous goods" system: www.sinatra-gost.ru
